go to main index know about us who we are and what we are provide ? we provide training on how to reach us send e-mail us
   

 

 

 

 

 

 

 

 

 

.
..                                                                      
Mobile control and monitoring of  Electricity meter

 

 

 

 

 

ntroduction

In this project we are using 8051 microcontroller.

 

We will study Mobile interface with Microcontroller

We will recharge the meter with mobile phone. We will  call to the particular no. then if we will press 1 then it will charge Rs.50 and if we will press 2 then it will charge Rs. 100.In this project we use one LCD screen. LCD screen display  the balance amount every time, LCD screen not only show the balance amount but at the same time  LCD display the unit consumption.  When the balance is zero then output is off.

 Now  for  continue the voltage we must need  to recharge the unit from the mobile phone.

 

LCD  FOR DISPLAY PURPOSE DISPLAY THE BALANCE AMOUNT AND UNIT CONSUME ( 2 LINE AND 16 CHARACTER)

 

MICROCONTROLLER. 89C51, 40 PIN CONTROLLER, 128 BYTE RAM, 4 K BYTE RAM. USED HERE FOR LCD DISPLAY AND START STOP FUNCTION. CHECK THE BALANCE AND CONTROL THE LOAD AS PER THE BALANCE.

 

IC 8870 , DTMF DECODER IC.

 

IC 8870 PROVIDE A GSM INTERFACE WITH THIS CIRCUIT. DUE TO THIS  IC WE DECODE THE CALL THE PROVIDE A BALANCE IN THE ENERGY METER AUTOMATICALLY.

 

IC 74154 IS A BCD TO DECIMAL DECODER ATTACH WITH THE MICROCONTROLLER TO INTERFACE WITH THE DTMF DECODER

 

5 VOLT REGULATED POWER SUPPLY TO PROVIDE A  REGULATED VOLTAGE TO THE MICROCONTROLLER UNIT.

.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5 VOLT REGULATED POWER SUPPLY CIRCUIT.

 

In this project firstly we use one step down transformer. Step down transformer step down the voltage from 220 volt Ac to  12 volt Ac. This Ac voltage is further converted into DC with the help of rectifier circuit. In rectifier circuit we use four diode. All the diodes  are arranges as a bridge rectifier circuit. Output of this rectifier is pulsating Dc. To convert this pulsating DC into smooth dc we use one capacitor as a filter components. Capacitor converts the pulsating Dc into smooth DC with the help of its charging and discharging effect.

Output of the rectifier is now regulated with the help of  IC regulator circuit. In this project we use positive voltage regulator circuit. Here we use three pin regulator. Output of this regulator is regulated voltage. If we use 7805 regulator then its means its is 5 volt regulator and if we use 7808 regulator then its means that it is 8 volt regulator circuit. In this project we use 5 volt dc regulated power supply for the complete circuit. Separate 9 volt dc power supply is used for the relay coil

  

 

 

DTMF DECODER

 In the  DTMF decoder circuit  we use one DTMF decoder circuit to interface the  mobile unit with this project. We  dial the number of the phone connected to the energy meter then phone is automatic on and  no we press a button 1 or button 2 to enter a value of 50 to 100 Rs in the meter. For this purpose we must need a mobile interface circuit with out project.  . In this interface circuit we use one main ic 8870. This ic 8870 decode the dtmf pulses into bcd pulse . This bcd pulses is further converted into decimal unit with the help of bcd to decimal decoder circuit.. For the bcd to decimal decoder circuit we use ic 74154 to decode the bcd signal to decimal signal.

 

 


 

             

      

                 

                                                                                                                                                                                

               1            2           3          4            5           6           7           8           9

 

 

 

 

 

PIN DESCRIPTION

 

 

IC 8870 is a DTMF (dual tone multiple frequency) decoder .It converts dtmf pulse into the equivalent BCD signal. Pin no. 18 and 10 of this IC are connected to the positive supply. This positive supply is from the 5 volt regulator circuit. Pin no. 9,5,6 are connected to the negative supply. Signal from the telephone line is in the form of dtmf pulse is applied to pin no. 2 of this IC through 2.2k ohm resistor and .1mfd capacitor. This signal is also connected to pin no. 3 through 100k ohm resistor. Pin no. 7 and 8 are connected to a crystal of frequency 3.7945 mh. Pin no. 16 and 17 of this IC is reset pin. Pin no. 11,12,13,14 are the BCD output of this IC.

 

Substitute ICs:  9170, 3170

 

 

 

 

 

 

 

 

 

 

 

COMPONENTS USED:

 

STEP DWON TRANSFORMER.                220 TO  9 VOLT AC      1 PC

DIODE                                              IN 4007                 2 PC

CAPACITOR                                              1000mfd                1PC

                                                          10 MFD,               1 PC

                                                           22 PF                              2 PC

                                                           .1 ( 104) MFD      2PC

 

IC.

8870        DTMF DECODER.

74154 BCD TO DECIMAL DECODER.

89C51         MICROCONTROLLER.

LCD  2 BY 16

 

TRANSISTOR:

          BC 548        NPN

          BC 558        PNP

 

RELAY

          12 VOLT DC SINGLE POLE SINGLE THROW

 

REGULATOR

          7805.

 

P.C.B COPPER CLAD BOARD ( GENERAL)

 

LED (3)

 

CRYSTAL.

3.58 Mhz

12  MHz

 

 

 

References:

 

8051 microcontroller book- Ali and mazidi

 

www.8051projectseasy.com

 

www.ludhianaprojects.com

 

www.atmel.com